DC 12-80V 30A Motor Speed Controller 0-100% Adjustable Electric LED PWM Driver Speed Regulator CCM6DS-K Light Dimmer Slow Start

1.Introduction:

CCM6DS-T is a DC12V-80V 30A 0%~100% PWM DC Motor Speed Controller with 30Amp Fuse.It can drive DC motor up to 30A with a CCM6DS-K control display panel. It is easy to use and can be directly connected to the motor and to adjust motor’s speed.

2.Feature:

1>.Slow Startand Slow Stop

2>.Dual 30Amp Fuseto protect circuit inside and motor

3>.DC 12-80V wide voltage so that adapt to more DC motors

4>.30A strong current output to provide enough driving capacity for the motor

5>.Adjust PWM from 0% to 100% which can control motor’s speed

3.Parameter:

1>.Product Name:CCM6DS-T 12-80V 30A PWM DC Motor Speed Controller

2>.Work Voltage:DC12V- 80V

3>.Drive Current:30A(Max)

4>.Control Power:12V/250W;24V/350W;48V/500W and so on;

5>.Duty cycle:0%~100%(Adjustable)

6>.Work Frequency:21KHz

7>.Work Temperature:-20℃~85℃

8>.Work Humidity:5%~85%RH

9>.CCM6DS-T Size:110*77*36mm

10>.CCM6DS-K Size:92*69*13mm

4.Package:

1>.1pcs CCM6DS-T 12-80V 30A PWM DC Motor Speed Controller

2>.1pcs CCM6DS-K Button/Display Control Panel

3>.1pcs 20cm PH2.0-5Pin Wire

5.Set Parameter:

1>.Press ‘MENU’button enter into set mode and switch parameter SET1~SET5.

2>.Press ‘UP’and ‘DOWN’buttons to change parameter value.Keep press can change value quickly.

3>.The first bit is mode and the remaining 3 bits is mode parameter value.

4>.E.g: display ‘2.010’means that the current display mode is SET2 and the parameter value is ‘010’.

5>.Press ‘RUN/STOP’button to save parameter and exit set mode to start running.

6>.’SET1’Function: 000-100 and display as ‘1.xxx’which is used to set motor slow starttime. Time from starting to 100% speed. Set time range is 0~10.0s and the default value is 1s. So ‘xxx’is 000 to 100. Note: ’090’means 9.0s.

7>.’SET2’Function: 000-100 and display as ‘2.xxx’which is used to set motor slow stop time. Time from press stop button to complete stop. Set time range is 0~10.0s and the default value is 1s. So ‘xxx’is 000 to 100. Note: ’090’means 9.0s.

8>.’SET3’Function: 000-080 and display as ‘3.xxx’which is used to set minimum speed value. Set range is 0%~80% and the default value is 0%. So ‘xxx’is 000 to 80. Note: ’070’means 70%. This value must be less than SET4.

9>.’SET4’Function: 000-100 and display as ‘4.xxx’which is used to set maximum speed value. Set range is 0%~100% and the default value is 100%. So ‘xxx’is 000 to 100. Note: ’070’means 70%. This value must be greater than SET3.

10>.’SET5’Function: 001, 002, 005, 010, 015, 020, 025 and display as ‘5.xxx’which is used to set speed regulation step size value. In normal display status, each time you press the ‘UP’or ‘DOWN’button , the speed changes 1%, 2%, 5%, 10%, 15%, 20%, 25%.

6.Use Steps:

1>.Select the matching power supply and DC motor.

2>.Connect DC motor at output terminal which has mark ‘MOTOR +’and ‘MOTOR -’as wiring diagram.

3>.Connect motor driver and button/display panel by 5Pin wire.

4>.Input work voltage at input terminal which has mark ‘INPUT+’and ‘INPUT-’as wiring diagram. Note:The positive and negative poles of the power supply must be connected correctly.

5>.Set parameter and adjust motor speed.

7.Note:

1>.It can output voltage same to input voltage.So the input voltage must match the motor’s work voltage.

2>.Please pay attention to the positive and negative poles of the power supply. It can't be connected reversely.

3>.It just can input DC power supply.

8.Application:

1>.Cooling equipment control

2>.Heating equipment control

3>.Irrigation system

4>.Lamp adjust brightness