8 Channel 230VAC Radio Receiver Garage Door Garage On / Off Radio Controller / Radio Receiver 10A

manuel http://einausschalten.com/0060427-y.pdf

delivery
1 x receiver


characteristic
Wireless control, easy to install.
LED indicator: working status is clear at first glance, chip is more compatible with remote control of fixed code and learning code, easy to use.
With learn button you can simply delete the code or learn.
Application: light, TV, motors, fans, cameras, video signals, audio signals, electrically operated doors / locks / windows / blinds / cars or other appliances.
You could turn the receiver on / off with a remote control from any location within a reliable distance. The wireless radio signals can run through walls, floors and doors
Reliable control: The transmitter (encoding) and the receiver (decoding) use an 8-bit code.
One or more transmitters can simultaneously control one or more receivers.
If you are using two or more receivers in the same place, you can set them with different codes.

parameter
Item Type: Switch
Model: APAC-8S
Operating distance: 200M
Type of switch: remote control
Channel: 8 channels
Working temperature: -10'C- + 70'C
Operating voltage: 230VAC
Working voltage range: AC110 ~ 240V or DC0 ~ 28V (that is, it is relay output, DC or AC can control devices)
Retirement current: ≤7A
Working frequency: 315MHz / 433MHz
Sensitivity: ≥-107dBm
Encoding type: learning code
PCB Size: 122 * 73 * 20mm
Housing Size: 126 * 80 * 30mm

Control Mode Description
Toggle (1 button on / same button off)
Latch (1 key on / other key off)
Momentary (pushbutton function, relay moves as long as button is pressed)
 
Set the control mode
Toggle: When the receiver is in the LEARNING state, press the 1 button on the remote control.
Toggle (Channel 1 ~ 8: Press -> Open; Press again -> Close.
Press button 1, channel 1 is switched on, press again 1, channel 1 is switched off.
Press button 2, channel 2 is switched on, press again 2, channel 2 is switched off.
etc...
 
Momentary: When the receiver is in the LEARNING state, press the 2 button on the remote control.
Currently (Channel 1 ~ 8: Press and hold-> Open, Clear -> Close.
Press button 1, channel 1 is switched on, release button 1, channel 1 is switched off.
Press button 2, channel 1 is switched on, release button 2, channel 2 is switched off.
etc...

Latch: When the receiver is in the LEARNING state, press the 4 button on the remote control.
Control Mode Latched (Channel 1 ~ 8: Press -> Open, other relays off, Press other key -> Close.
Press A, channel 1 is switched on; Press B button, channel 2 is switched on, and channel 1 is switched off. etc..

Toggle + Momentary: When the receiver is in the LEARNING state, press the 8 button on the remote control.
Control Mode Toggle (Channel 1 ~ 4) + Control Mode Momentary (Channel 5 ~ 8)
 
Note: If you learn the other function, you need to delete the learned code.


Learning and steps
1. Press the learn button of the receiver until the LED indicator lights up, the receiver now remains in the status of READING.
2. Then you can press to your requirement drücken.Wenn the indicator LED flashes 1 times, it means that the Ablernen is successful.

Delete the learned code
Press and hold the receiver's learn button for 8 seconds until the LED indicator is off (the receiver can store about 30 different coding tones), it means that all stored codes have been successfully erased.

reach
Max. Range in free field: 200m (maximum range of the sensor / signal under optimal conditions, or in the open field / with clear visual connection.)
Note
The hand transmitters have a range in the free field of about 200m. Constructions, interfering radiation and interference fields reduce the range.
The control should not be installed in the direct vicinity of metallic surfaces. Strong local transmitters (e.g., radio headphones whose transmit frequency is identical to the controller may interfere with reception.)