100m AC 220V Wireless Remote Control Switch Two Channels Wireless Remote Control Relay Output Wireless Remote Control Switch

Feature
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
Wide voltage: Suitable for voltage AC85V-260V, ensuring long-term stable operation in circuits with different voltage environments
Switching power supply step-down circuit: use the switching power supply chip LNK304 produced by American POWER Company to control the power supply, quality assurance, stability and durability.
Easy use:Wireless control, easy to install. Wireless RF signal can pass through walls, floors, doors or windows. You can use two or more units in the same place.
Reliable control: The receiver only works with the transmitter which use same code. One/several transmitters can control one/several receivers simultaneously. You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Stable: Insurance resistance with Varistor effective protection of the circuit board greatly improves the service life of the entire remote control switch

Working Range(actual Test distance: 2360M without obstacles in open space)
With a transmitter to form a complete set, the maximum working distance can reach 3000M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.

Parameters:
Working voltage: AC85-260V
channel: 2 channels
Working frequency: 315MHZ
Receive sensitivity: >-114dB
Contact capacity: ≤10A/250VAC; 10A/30VDC
Control Modes: Toggle/ Momentary / Latch
Coding type: learning code
Maximum Working Current: 10A / each channel
Operating Temperature: -20 ° C to +70 ° C
Remote control size: 135*42*25mm
Receiver board size: 68*48*22mm

Control mode
Momentary------------Press the Transmitter button A, the receiver relay A is ON, release button A; the receiver relay A is OFF,
Toggle---------------Press transmitter button A for 1 time , the receiver relay A is ON, press button A again, the receiver relay A is OFF,
Latched------------Press transmitter button A, the receiver relay A is ON, Press transmitter button B, the relay A OFF.

Set the different control modes:
Toggle: Jumper on "T-PIN" + Middle PIN
Momentary: Jumper on "M-PIN" + Middle PIN
Latch: without jumper

Use Control mode:
Setting different control modes: (We have set the receiver in Latch mode before delivery, if you want to use other modes, do as following operation.)
Setting control mode Toggle
Control mode Toggle: Press -> On; Press again -> Off.
Press button 1 of the transmitter: Terminals “Relay-1” outputs AC power, the lamp 1 is on.
Press button 1 again: “Relay-1” stops outputting, the lamp 1 is off.
Press button 2 of the transmitter: Terminals “Relay-2” outputs AC power, the lamp 2 is on.
Press button 2 again: “Relay-2” stops outputting, the lamp 2 is off.

Setting control mode Momentary
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button 1 of the transmitter: Terminals “Relay-1” outputs AC power, the lamp 1 is on.
Release button 1 of the transmitter: “Relay-1” stops outputting, the lamp 1 is off.
Press and hold button 2 of the transmitter: Terminals “Relay-2” outputs AC power, the lamp 2 is on.
Release button 2 of the transmitter: “Relay-2” stops outputting, the lamp 2 is off.

Setting control mode Latch
Control mode Interlocking: Press -> On, Press another button -> Off.
Press button C of the transmitter: “Relay-1” outputs AC power, the lamp 1 is on.
Press button B of the transmitter: “Relay-2” outputs AC power, the lamp 2 is on.
Terminals “Relay-1” stops outputting, the lamp 1 is off.
Press button A of the transmitter: “Relay-2” stops outputting, the lamp 2 is off.

Learn method: Press the learn button once, the indicator lights up. At this time, press the button on the remote control, the indicator light goes out and the learn is successful.

Clear code:Press and hold the learning button for 8 seconds, the indicator lights up, then goes off, which means that the clear code is successful.