AC 220v 12 channel wireless remote control switch 220V 12 way multi-function receiving controller 500m

manuel http://einausschalten.com/0075201-y.pdf

delivery
1 x receiver
1 x transmitter with battery

characteristic
Wireless control, easy to install.
LED indicator: working status is clear at first glance, chip is more compatible with remote control of fixed code and learning code, easy to operate.
With the learn button you can simply delete or learn the code.
Application: Light, televisions, motors, fans, cameras, video signals, audio signals, electrically operated doors / locks / windows / blinds / cars or other devices.
You could turn on / off the receiver with transmitter (remote) from any location within a reliable distance. The wireless radio signals can pass through walls, floors and doors
Reliable control: The transmitter (Encoding) and the receiver (decoding) use an 8-bit code.
One or more transmitters can simultaneously control one or more receivers.
If you use two or more receivers in the same place, you can set them with different codes.

parameter
Article type: switch
Model: APAC-12S
Range: 200M
Features: AC230V input
Working Voltage Range of Relays: AC110 ~ 240V or DC0 ~ 28V (Relay Output Can Control DC and AC Devices)
Switch type: remote control
Channel: 12 channels
Working temperature: -20'C- + 70'C
Operating voltage: AC230V
Output current: ≤5A
Quiescent current: ≤10mA
Working frequency: 315MHz / 433MHz
Sensitivity: ≥-107dBm
Coding type: learning code
Size of receiver: 120mmⅹ73mmⅹ18mm
Size housing: 125mmⅹ80mmⅹ30mm
Antenna: with internal antenna

Control mode Description
Toggle (1 button on / same button off)
Momentary (Relay remains on as long as the button is pressed)
Latch (1 button on / another button off)

Set control mode
Toggle: When the receiver is in the state of LEARNING, press button 1 on the remote control.
Toggle (channel 1 ~ 12): Press -> Open; Press again -> Close.
Press button 1, channel 1 is on, press again, channel 1 is off. etc..

Momentary: If the receiver is in the state of LEARNING, press button 2 of the remote control.
Currently (channel 1 ~ 12): Press and hold-> open; Share -> Close.
Press button 1, channel 1 is switched on, release button 1, channel 1 is switched off. etc..

Latch: When the receiver is in the state of LEARNING, press button 3 on the remote control.
Control mode Latched (channel 1 ~ 12): Press -> Open, switch off other relays; Press another key -> Close.
Press button 1, channel 1 is on; Press button 2, channel 2 is on, and channel 1 is off. etc..



Toggle + Momentary: When the receiver is in the state of LEARNING, press button 4 on the remote control.
Control Mode Toggle (Channel 1 ~ 6) + Control Mode Momentary (Channel 7 ~ 12)

Toggle + Momentary: When the receiver is in the state of LEARNING, press button 5 of the remote control.
Control Mode Toggle (Channel 1 ONLY) + Control Mode Momentary (Channel 2 ~ 12)

ATTENTION: If you want to use other control modes, you need to clear the original modes.

Learning method and steps
1. Press the learn button on the receiver until the LED indicator lights. The receiver now remains in the status of LEAVE.
2. Then you can press the button after your request. If the indicator LED flashes 1 time, it means that the learning is successful.

Delete the learned code
Press and hold the receiver's learn button for 8 seconds until the LED indicator turns OFF, it means that all stored codes have been successfully erased.

reach
Max. Range in free field: 200m (maximum range of the sensor / signal under optimal conditions, or in free field / with free line of sight.)
Note
The hand transmitters have a range in the free field of about 200m. Buildings, interference and interference fields reduce the range.
The controller should not be installed in close proximity to metallic surfaces. Strong local transmitters (e.g., wireless headphones whose transmission frequency is identical to the controller) may interfere with reception.)